Wireless Addressable Fire Alarm System Installation

https://www.asmag.com/download/2026-hikvision.pdf

Product Ranges

CCTV, IP Camera, Access Control, Intrusion Detection, Management Platform, Building Automation, Home Automation, Security Services, Personal Safety, Fire & Safety, Solution

Vedard Alarm Security Export Sales Company
Country: China
City: Quanzhou
Address: Qingmeng industrial zone
Contact Person: Karl Liang

Wireless Addressable Fire Alarm System Installation

Source: https://www.vedardsecurity.com/Wireless-Addressable-Fire-Alarm-System-installation-ezp-50

Date: 2026/04/09

https://www.vedardsecurity.com/Wireless-Addressable-Fire-Alarm-System-installation-ezp-50
This document details the full installation, debugging, operation procedures and precautions for the JB-TB-TC5126W wireless fire alarm control panel, with TC-ZJ402 wireless signal extender as the matching auxiliary device, covering core steps from pre-installation preparation to post-debugging acceptance, fault resolution and key operational notes.

1. Core Installation Workflow

Confirm the control panel’s type, quantity, installation position per drawings → Install the panel → Device network access → Test communication (add signal extender if communication fails; proceed if normal) → Programming → Debugging → Acceptance check.

2. Device Network Access & Communication Distance Test

2.1 Pre-access Network Settings (Control Panel)

Network segment setting: Enter Menu→6 Network setting (password 111111)→2 Wireless setting; set different frequencies for different segments (e.g., 464.2MHz/466.2MHz) to avoid interference, frequency range related to 464-466MHz.

Wireless address: 1-254 for field devices; consistent address required between panel and signal extender in debugging.

Power consumption level (4 levels): Lv1 (max 32 devices/loop, fault report in 100s); Lv2-4 (max 64 devices/loop, fault report in 2h/12h/15h respectively); Lv4 is recommended (impacts battery life).

Loop setting: 1-2 loops available for the panel, set per actual usage.

2.2 Device Network Access/Exit & Status Test

Access: Menu→5 System settings (111111)→4 Wireless registration; select loop/sensitivity/device type, press the device’s network button 3x (green light flashes 3x) to send access request.

Exit: Under wireless registration interface, press the device’s network button 3x (green light flashes 3x) to send exit request.

Status test: Press the network button once (green light flashes once); panel displays loop/address + R/T signal strength (0-130, smaller value = better communication) for successful access.

Factory reset: Tap the network button 5x within 10s of device power-on (alarm light on for 10s).

2.3 Communication Distance Test

Check panel signal reception/strength at the device’s designated position; add a signal extender if the panel has no response.

3. Signal Extender (TC-ZJ402) Debugging & Addition

Acts as a data bridge between field devices and the panel to extend communication range; debugging includes panel side and software side settings, with on-site installation/test after setup.

3.1 Panel Side Setting

Enter Menu→6 Network setting (111111)→5 Signal extender setting; set wireless loop (1-2), relay link (1-8, 5 extenders max/link), start/end device address (1-64) and mode (0-Add/1-Del/2-Clr). For discontinuous device addresses, set repeatedly; split address ranges for different links (e.g., 1-32/33-64 for Link1/2).

3.2 Software Side Setting

Connect RF470 wireless communicator to computer, set COM port in debugging software, fill in consistent panel wireless address, panel ID, loop number and frequency with the panel.

Set extender parameters per on-site device distribution (floor/address range); distinguish device types (0－ for direct transmission, X－ for relay transmission by lower-level extenders).

Power on the extender (running light flashing), press the setting button 5x (three indicators flash), send settings via software (100% progress = complete), press the setting button again to exit setup mode (only one extender can be set at a time).

3.3 On-site Test & Installation

Test signal strength (fault light flashes 3x then off = good; off after 3s = poor, adjust position); avoid channel collision from close installation.

Max 8 extenders/loop, 5 extenders/floor for the panel; add multi-floor extenders if single-floor range is insufficient.
Install extenders away from power distribution shafts, humid/EMI/shielded areas; keep power adapter connected for continuous power supply.

4. Physical Installation of Devices

After debugging, install via self-tapping screws (recommended) (drill wall + expansion plug) or 3M glue (only for non-drillable surfaces; ensure

smooth/dry/clean installation surface, regular adhesion checks). Recheck panel communication (loop/address/signal) post-installation; add extenders if no display.
5. Control Panel Debugging & Linkage Test

Panel debugging: Compile device annotation/linkage programs per coding table; upload via USB or manual input on the panel.

Linkage test: Trigger alarm via MCP/smoke detector/temperature sensor; verify linkage device action, then reset all devices/panel immediately to avoid battery drain.

Device reset: Special key for manual call points/fire hydrant buttons; panel operation for other devices.

6. Critical Precautions

Plan device type/quantity/loop division pre-access; avoid idle addresses and signal extender cross-loop transmission.

Set panel loop segment/address pre-access (no modification post-access to prevent communication failure).

Match panel-side extender settings when adding extenders (no panel response to device alarms if not set).

Avoid simultaneous network access for multiple panels (short distance) to prevent wrong access/accidental exit.

Set extender start/end addresses per actual responsible device ranges (panel overwrites duplicate settings).

Timely reset alarm/feedback devices; long-term alarm drains battery.

Factory reset devices for single-point/channel deletion on the panel to avoid heartbeat interference.
Fix the antenna near (not on) the control panel; one extender set at a time.

7. Common Problems & Solutions

Troubleshoot typical issues including no panel response post-device access (check extender transmission/working status/settings), device access failure (power cycle/ factory reset/ replace low battery), communication fault (add extender/ replace battery), no linkage (check panel programs/auto mode), I/O module input/output fault (add 10K resistor/ turn off line check/ re-operate network access), and base separation fault (recover device base fit).

Vedard Alarm Security Export Sales Company

More News