ComNet supports Vietnam veterans traveling wall with wireless Ethernet transmission

ComNet supports Vietnam veterans traveling wall with wireless Ethernet transmission
The American Vietnam Veterans Traveling Tribute Wall is a scaled down replica of the Vietnam Veterans Memorial in Washington, DC that has been seen by millions since its dedication in 1982.

With the potential for that many people gathering in one location, keeping everyone safe and secure was paramount. System integration for the event was assigned to ABF Security Systems of Fenton, Missouri. With the assignment to provide security to this very visible, yet temporary event, Mike Polizzi, ABF Security President turned to respected Security Industry Manufacturers’ Representatives RW Kunz and Associates to recommend a comprehensive solution to this challenge. RW Kunz’s Mark Bowers and Brad Cooper selected equipment from Pelco for the IP camera and recording equipment and chose ComNet Communication Networks to provide the network transmission equipment.

As the Wall was to only be displayed temporarily, the traditional method of running cables or using fiber optic transmission was impractical. Facing a unique challenge, Kunz’s Bowers recommended to ABF that they employ the new ComNet NetWave wireless Ethernet product line. This all-new NetWave product line is very easy to install and use, and was the perfect solution in this application. In fact, prior to the arrival of the Traveling Tribute, a site survey was performed. At the time of installation, trailers and tents supporting the event were in the wireless transmission path. However, even with this these potential obstacles in the line of sight, the cameras all came up without any trouble. Four Pelco IM Surevision 1.2 megapixel day/night AF low light WDR rugged cameras were placed at strategic locations, the furthest being 90 yards away from the monitoring location. Two cameras were observing the backside of the wall and two more were observing activity from the front. This setup gave complete coverage of the entire event.

To get the video back to the head-end monitoring location, the ComNet NetWave NW1 point to multipoint models were selected. The four NW1 client units were installed close to the camera locations. The camera output was 10 frames per second at 1280 × 720 resolution. Using H.264 compression, each of the four cameras required 2.5Mbps of bandwidth. The Netwave NW1 handles up to 95Mbps, so the total 10Mbps bandwidth from this installation required only a small percentage of the NetWave NW1 capability. The IP-Video was then seamlessly transmitted back to a NW1 Access Point, where it was all collected and fed into a Pelco DSSRV recording system.

One of the many advantages the NetWave wireless Ethernet system offers is the simplicity of set up and use. Mike Polizzi and crew from ABF Security Systems, the integrator on the project report the NetWave system was very easy to install and use, and the picture quality was great. According to Kunz’s Mark Bowers, “setting up the NetWave gear was as easy as it was promoted. It truly lives up to the “Power, Point and Play” promise ComNet pledges.”

The Saint Louis County Police Department monitored the event constantly for the entire four days the Wall was in place. No incidents occurred and the system operated flawlessly during the entire event.

The event drew a very large crowd consistently over the course of the event. Even though both the wall and security network were considered temporary, there is no doubt as to the long-term effectiveness of the ComNet NetWave wireless Ethernet product line.

NetWave is wireless Ethernet transmission made easy

Power, point and play. Power up and point the units and start transmitting Ethernet. The ComNet NetWave line consists of an easy pre-packaged Point-to-Point kit that contains everything you need to establish remote connections to Ethernet edge devices. Also available are Point-to-Multipoint models allowing multiple client/camera/networked edge device locations to connect to a single access point.

NetWave will support up to 95Mbps throughput and supports a wide range of Ethernet devices such as megapixel/HD cameras, DVRs, encoders/decoders and web servers. NetWave is secure and uses encryption to prevent unauthorized access to the system. These units also offer the option to be powered by the included Power Injector or by an IEEE 802.3af/at PoE switch.


Product Adopted:
Wireless Transmission
Share to:
Comments ( 0 )

asmag.com provides weekly and monthly e-Newsletters which include the latest security industry news, vertical solution case studies and product information.



Please key in code
Which Security 50 company will you place your bet on that grew the most this year?
Hikvision Digital Technology
Dahua Technology
Axis Communications
Avigilon