3.5 inch HVT CCTV Tester with PTZ controller, PING Tester, POE Test and optical power meter

The new cctv tester, built-in high definition 3.5”LCD-TFT 480（RGB）x320

full-view display screen, easy and directly displays the camera image quality

Support PAL/NTSC

LCD screen brightness/Contrast/Color Saturation adjustable. Suitable for field construction and maintenance work

2. Video signal level test

Test video signal strength attenuation, longer video signal cable will cause the image to be dim, and reduce the image dynamic range, video signal is too strong, it will cause the virtual shadow, and reduce the sharpness of the image.

　It also can real-display the video level value, if out of range, notices will be display in the screen.

3. PTZ controller

Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset position.

4. Enhanced Color bar generator

Video Generating, the PAL/NTSC multi-system color bar video generator (Eight-system switchable, transmit/receive eight-system colorful imagines). By receiving the video color bar to test the video channel whether transmit normally. And judge whether the color is different, because of the transmission loss or interference, it suitable for Video transmission of the field tests, such as optical video transmitter and receiver, video cable etc.

The new function color bar can test the image whether shift.

The color bar (red, green, blue, white, black) test the monitor whether have white or black dot etc.

5. DC12V 1A output power

Power the camera with DC12V (1A) power output from the tester. It is helpful for demo and testing when the power supply is not available.

6. Audio testing

Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable.

7. Cable tester

Test LAN cable or telephone cable.

Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting status, cable type and the sequence of wires will be displayed, as well as the serial number of the cable tester kit.

8. PTZ controller

Search the Control protocol code from Multifunction keyboard or DVR by RS485 /RS232 interface, test the PTZ control command data whether received anomaly and RS485/RS232 data transmission.

Screen displays 16 hexadecimal codes such as

PELCO-P：A0 00（Add） xx xxxxxx AF xx

PELCO-D：FF 01（Add）xx xxxxxxxx

9. PTZ address scanning

Search up the ID of PTZ camera. Help the engineer search the speed dome address quickly.

10. Image magnification（10xZoom）

Set image 10x zoom, can view and display the details by 1x、2x、3x、4x、5x、6x - 10X zoom in the monitor and tester.

11. Video snapshot

Capture the video image and save the current video frames as JPEG file

12. Video record

Record and save the current video in the SD card

13. Video playback

Video image and record files are saved in the SD card. Storage file directory can be created according to the date

14. Port flicker

The tester will send special signals to make the connected POE port flicker at special frequency, which will enable the installers to easily and quickly find the connected ethernet cable. This function can prevent mistakenly insertion or disconnection non-corresponding cable to artificially interrupt network connection.

15. IP address scan

In digital IP surveillance applications, if IP camera’s IP address is not clear or forgotten; the device cannot be used .

IP address scan can quickly search the connected IP camera or other network device’s IP address.

16. Link monitor

To add an IP camera or other network device to the current network group, the new IP address must not be occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can check if the new setting IP address is occupied.

17. PING test

PING is the most conventional network debugging tools; It is used for testing if the connected IP camera or other network equipment’s ethernet port is working normally and the IP address is correct.

18.POE tester

It can test the POE voltage when the POE switch is supplying the POE power to IP camera. It can clearly display the power+ and power- on the ethernet cable pins, each cable pin’s voltage and the failure connection of cable pin series numbers.

19. LED lamp

It is useful for the Engineer to install and maintain security system at night. LED On/Off pressing button, easy operation.

20. F1、F2 User-defined shortcut keys

The user-defined shortcut key is designed for improving the efficiency for the engineer, anytime press, easy to operate.

21. TDR Break-point and short-circuit measurement (optional function refer to the last page)

New function: TDR cable testing, accurately measure BNC cable, network cable, control cable break-point and short-circuits location. It improves working efficiency.

22. Optical Power Meter

The New tester adopts the most advanced handheld instrument specific integrated chip , achieve ultra-low power operation, with the 3.5 TFT-LCD High-definition screen display ，five wavelength calibration points 1625nm、1550nm 、 1490nm 、 1310nm 、 1300nm 、 850nm.Linear or nonlinear optical power display, it can measure the optical power value, and also be used for Relative measurement of optical fiber link loss. It is necessary tool for fibre-optic communication, cable television system and security system maintenance.

23. Cable scan

Send the specific signal, easy to find the connected cable.

Model HVT CCTV TESTER HVT2612 ( 6th generation)

Video Test

Signal mode NTSC/PAL (Auto adapt)

Display 3.5 inch digital TFT-LCD ,480（RGB）x 320 resolution

LCD adjustment Brightness, Contrast, Saturation adjustable

Video IN/OUT 1 channel BNC Input & 1 channel Output

Video Output Mode 1.0 Vp-p

Video Level test

Level test Video signals measured in IRE or mV

PTZ controller

Communication Support RS232 and RS485

PTZ Protocol Compatible with more than 30 protocols such as PELCO-D/P, Samsung, Panasonic, Lilin, Yaan, etc.

Baud Rate 600，1200，2400，4800，9600，19200,57600,115200bps

Video Signal Generation

Color bar generator Output one channel PAL/NTSC color bar video signal for testing monitor or video cable.(red, green ,blue, white and black color )

UTP Cable Test

UTP cable test Test UTP cable connection status and display in the screen. Read the number of the test box.

DC12V 1A power output

DC12V power output Output DC12V1A power for camera

Cable Scan

Cable Scan Search the cable by the audio signal

Audio input test

Audio input test test the pickup and other audio equipments on the front-end

RS485 data analysis

Data Monitor Captures and analyzes the command data from controlling device

10 x zoom of image

Image 10x zoom 10x zoom image display and video out

Photograph,Video record, Record playback

Photograph snapshot and save the current image as JPG file

Video record Video record and storage the file

Record playback To view the storage file in the SD card

Port flicker

Port flicker

Find the connected POE port quickly.

IP scan, Link monitor, PING test

IP scan Find out the connected IP camera or the other network equipment IP address quickly.

Link monitor Check the IP address whether is occupied

PING testing Test IP camera or Ethernet port of the other network equipment whether work normally, and check the IP address

POE tester

POE tester Display the power supply voltage and cable connection states

Optical power meter

Calibrated Wavelength(nm) 850/1300/1310/1490/1550/1625nm

Power range(dBm) -70～+10dBm

Sensitivity(nW) 0.001nW

Connector type FC/PC

Data hold Display data hold

Relative measurement Display the measurement value

TDR Tester

TDR Tester breakpoint and short circuit measurement(BNC cable, telephone cable)

POWER

Power Adapter DC 5V（1.5A）

Battery Built-in 3.7V Lithium polymer battery ,3000mAh

Rechargeable After charging 3-4 hour, working time lasts 11 hours

Low Consumption Energy saving technology, the battery icon real-time display

Parameter

Operation setting English/Chinese and other languages OSD menu

Auto off 5-60 (mins)

Keytone On/Off

General

Working Temperature -10℃-+50℃

Working Humidity 30%-90%

Dimension/ Weight 194mm x 112mm x 48mm / 540g